- Maximum Speed: 32 kn
- Beam: 14' 2''
- Hull Material: Fiberglass
- Max Draft: 3' 5''
- Fuel Tank: 2 x 515|gallon
- Fresh Water: 1 x 132|gallon
- Holding: 1 x 60|gallon
- Cabins: 3
- Heads: 2
1810 views
(Major $49,000 Price Reduction August 5, 2023)
This 2003 Cranchi Mediterranée 50 has undergone significant updates, specifically in the last 12 months since the owner's purchase her in 2021. She is currently being stored indoors and can be viewed by appointment. This boat has an excellent layout. Below are a list of her features. Please read the description section for a full list of updates.
Three Stateroom & Two Head Layout
Twin Volvo D-12 Diesel Engines with Approximately 1,150 Hours
Fischer Panda Generator
Bow Thruster
Air Conditioning & Heating
Garmin & Raymarine Electronics
Hydraulic Tender Garage
Much More!
12-29-2021 Change oil pump and filter
12-29-2021 Replace coolant port and starboard engine
1-28-2022 Straightline fabrication/interior bedding
replacement, exterior helm and cockpit
cushions, replacement of complete canvas
enclosure
1-28-2022 NorEast marine/replace chiller system
2-25-2022 Thru hulls – Replace engine generator
and chiller intake thru-hulls. Forespar
valves. New strainers and supply hoses
Dry fit engine intake valves. Float valve
and stem into epoxy, glue stem with
life-caulk. Antifouling coating. Replace
bonding wires on engine thru-hulls
2-25-2022 Install general zincs exterior
3-31-2022 Sand and paint bottom one coat
3-31-2022 Volvo shift problem
3-31-2022 Thru hulls – replace engine generator
and chiller intake thru-hulls. Forespar valves
cleaned all mounting surfaces. Dry fit
Forespar aft thru-hulls with backing pads
glue stem on the exterior with lifeseal
glue and float backing pads attached to
thru-hulls in place. Install new strainers
and supply hoses. Dry fit engine intake
valves, make backing plates. Float valve
and stem into epoxy, glue stem with
life-caulk. Strip away old paint on the
exterior, prime surface and apply antifouling coating. Replace bonding wires on
engine thru-hulls.
5-27-2022 Install engine zincs
5-27-2022 Change belts main engine
5-27-2022 Repair bilge pump and shower sump
5-27-2022 Repair fresh water leak in water system
5-27-2022 Replace Crankcase and air filters main eng
5-27-2022 Remove broken fitting Stbd Trans cooler
5-27-2022 New docking fenders with covers & lines
6-30-2022 Change fuel filters main engines
6-30-2022 Replace broken trim cylinders/replace
trim pump and four trim cylinders
6-30-2022 HeadSync toilet repair, bow seal, vac pump
6-30-2022 Replace forward hatch
6-30-2022 Compound and wax hull
6-30-2022 Compound and wax cockpit
6-30-2022 Touch up gel-coat starboard side
6-30-2022 Air conditioning ducting – make access
panels for a/c ducting replacement
6-30-2022 Replace additional ducting
7-29-2022 NorEast marine/replace chiller system
8-30-2022 Remove backs of seats onboard, remove
nose cone in engine room and cockpit
seating
8-30-2022 Straightline fabrication/interior bedding
replacement, exterior helm and cockpit
cushions, replacement of complete
canvas enclosure
9-29-2022 Cay electronics
1-31-2023 Change fuel filters x 4
1-31-2023 Install general zincs/exterior and internal
engine
1-31-2023 Replace batteries
1-31-2023 Change engine impeller
1-31-2023 Service thruster
1-31-2023 House bank battery charger
1-31-2023 Charger generator battery
1-31-2023 Battery cables and battery cable ends/
make new battery cable jumpers,
change cable ends
1-31-2023 Generator; remove and rebuild by
Fischer Panda
1-31-2023 Clean air intake filters
1-31-2023 Build crate to ship generator
1-31-2023 Paint bottom 2 coats
1-31-2023 Compound and wax hull
1-31-2023 Hull touch ups
2-27-2023 House bank battery charger
2-27-2023 Charger generator battery
2-27-2023 Compound and wax superstructure
2-27-2023 Hull touch ups
2-27-2023 Remove old sea deck/wood not sealed
properly
2-27-2023 Deck areas sand all surfaces, fill all holes
Contact our team to schedule a private showing.